16 Relay Module
with LEDs
(Fully Assembled PCB)
Product Use
This 5 VDC Relay Module is especially developed for Automotive or Hobby use, allowing microcontroller to switch on any high current load.
Command Signal of low current at low voltage (Typically 0.5 milliAmpere @ 3.3 V DC) into the Relay Module electronically switches ON a Higher current Load (up to 10A) at typical automotive system voltage (10 VDC to 14.4 VDC).
In constant ON applications it can carry up to 10 Ampere load.
The 5 VDC Relay Module can be used to switch on AC loads up to 250 VAC, such as lights, fans, motors and other devices ON/OFF while keeping them isolated from the microcontroller.
The LEDs located on the PCB are ON when any corresponding Input Pin (#2 to #17) is connected to Ground Common with Vcc.
Control Input can be connected directly to any output pin of PARALLAX PROPELLER microcontroller without need for any resistors.
The 5 VDC Relay Module is also Arduino Compatible.
Features
- Opto Isolated Inputs
- Control Relay Module with a simple high/low Command signal
- Input ON Monitoring LED
- Power ON Monitoring LED
- Nominal Voltage 5V
- Operating / Releasing Time ≤ 1 ms / ≤ 1 ms
- Over 100,000,000 Electronic Cycles Life
Connections
INPUT
- GND (Common System Ground)
- CIN1 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN2 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN3 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN4 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN5 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN6 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN7 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN8 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN9 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN10 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN11 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN12 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN13 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN14 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN15 = ON Command Signal 3.3 VDC to 5 VDC -
- CIN16 = ON Command Signal 3.3 VDC to 5 VDC -
- Vcc = 5 VDC +
OUTPUT (Each Relay)
- Relay NO = Normally Open Contact
- Relay C (Common Input)
- Relay NC = Normally Closed Contact
POWER
- GND (Common System Ground)
- Vcc Power +5VDC
Product Specifications
| Relay Coil source voltage (min/max) | VDS | 4.5 / 5 | V |
| Relay Contact load Current (max) | IL | 10 | A |
| Relay Contact load Voltage (max) | 240 | V AC | |
| Relay Contact load Voltage (max) | 30 | V DC | |
| Command Signal Voltage (low) | VCC | 0.0 | V DC |
| Command Signal Current @ 5.0V | Ion | -3.75 | mA |
| Stand-By ON Current @ 5.0V | Ion | 3.2 | mA |
| Power Consumption (LED) board ON | Pon | 16 | mW |
| Power Consumption (LED) each input | Pon | 20 | mW |
| Operating Temperature | Ton | 20 to 140 -6 to 60 |
°F °C |
| Module Size | 180 x 80 x 18 | mm |
Module Circuit Diagram
NOTE: Relays 1 to 4 shown, relay circuits for 5 to 16 are identical.
Pricing
US $30.00 each